CATEGORIES
SHEETS CAN DOWNLOAD HERE TSE DOCUMENT
DID YOU SEE? CE DOCUMENT
DID YOU SEE? OUR CATALOG YOU CAN
DOWNLOAD AS PDF
- Tile Adhesives and Joint Fillers Fuga
- Repair Mortars and Grouts
- Thermal Insulation Products
- Industrial Flooring Products
- Granito Microbeton
- Tekno Stone Carpet
- Restoration Products
- Waterproofing Products
- Concrete Admixtures
- Construction Reinforcement Products
- Construction Chemicals General List
SHEETS CAN DOWNLOAD HERE TSE DOCUMENT
DID YOU SEE? CE DOCUMENT
DID YOU SEE? OUR CATALOG YOU CAN
DOWNLOAD AS PDF
Teknobond 300 NB Epoxy Primer For Wet Surfaces
Teknobond 300 NB is epoxy based, two component, low viscosity, solvent free, primer for moist and wet surfaces.
TDS Technical Document Sheet
Teknobond 300 NB is epoxy based, two component, low viscosity, solvent free, primer for moist and wet surfaces.
Areas of Usage
• Lining concrete surfaces, cement screed and epoxy mortars,
• On normal, hot surface, moist and wet surfaces,
• As a primer before all epoxy and polyurethane floor coverings,
• As a binder for epoxy based bedding mortar and mortar coverings,
Features and Benefits
• it acts as a moisture barrier by providing very good adherence to moist and wet surfaces
• Low viscosity,
• Has good penetration properties,
• High bondresistance,
• Solvent free,
• Easy to implement,
• Waiting times are short,
• AII purpose
• it can be used outdoors,
Application lnstructions
The application surface should be free of all kinds of dust, dirt, weak and friable particles, cements herbet residues, oil and grease and dry. Concrete substrate must be clean, robust and sufficiently Compressive Resistance (at least 25 N/mm2), tensile strength (pull off) at least 1 .5 N/mm2. Application surface, to ensure maximum adhesion resistance, pressurized air holding, ete. it must be cleaned using methods.
After adding component B to component A, mix it for 2-3 minutes until it has a homogeneous color (up to 400 RPM) with a low speed electric stirrer.
Make sure that a continuous, nonporous layer is covered by the surface. lf necessary, apply two storey of primer. Teknobond 300 NB can be applied with brush, roller or spray gun. lmmediately after application, tools should be cleaned with TEKNO THINNER without hardening. Hardened product can only be mechanically cleaned.
Application Notes / Restrictions
• Do not use it below the permitted minimum temperature to complete the hardening of the material. Low temperatures will slow hardening and high temperatures will speed hardening. Pot life will vary depending on the temperature.
• The floor temperature without curing should be at least 3°C above the condensation point.
• The product may cause sensitization by skin contact. Protective gloves, mask and goggles should be worn. in case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
0°C below the product stored for a long time can be observed crystallization. lf the crystals are dissolved, the product can be used without any problems by returning to room temperature.
• Color losses can be yellowing of the product, which is hardened due to direct sunlight (UV)
• Lining concrete surfaces, cement screed and epoxy mortars,
• On normal, hot surface, moist and wet surfaces,
• As a primer before all epoxy and polyurethane floor coverings,
• As a binder for epoxy based bedding mortar and mortar coverings,
Features and Benefits
• it acts as a moisture barrier by providing very good adherence to moist and wet surfaces
• Low viscosity,
• Has good penetration properties,
• High bondresistance,
• Solvent free,
• Easy to implement,
• Waiting times are short,
• AII purpose
• it can be used outdoors,
Application lnstructions
The application surface should be free of all kinds of dust, dirt, weak and friable particles, cements herbet residues, oil and grease and dry. Concrete substrate must be clean, robust and sufficiently Compressive Resistance (at least 25 N/mm2), tensile strength (pull off) at least 1 .5 N/mm2. Application surface, to ensure maximum adhesion resistance, pressurized air holding, ete. it must be cleaned using methods.
After adding component B to component A, mix it for 2-3 minutes until it has a homogeneous color (up to 400 RPM) with a low speed electric stirrer.
Make sure that a continuous, nonporous layer is covered by the surface. lf necessary, apply two storey of primer. Teknobond 300 NB can be applied with brush, roller or spray gun. lmmediately after application, tools should be cleaned with TEKNO THINNER without hardening. Hardened product can only be mechanically cleaned.
Application Notes / Restrictions
• Do not use it below the permitted minimum temperature to complete the hardening of the material. Low temperatures will slow hardening and high temperatures will speed hardening. Pot life will vary depending on the temperature.
• The floor temperature without curing should be at least 3°C above the condensation point.
• The product may cause sensitization by skin contact. Protective gloves, mask and goggles should be worn. in case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
0°C below the product stored for a long time can be observed crystallization. lf the crystals are dissolved, the product can be used without any problems by returning to room temperature.
• Color losses can be yellowing of the product, which is hardened due to direct sunlight (UV)