Waterproofing Products

  TDS Technical Document Sheet   

  CE Document   

Product Description
Two component, waterproofing material based on polymer bitumen-rubber based, cracked, applied from the positive side.

Areas of Usage
• inTerrace,
• in the basement and curtain walls,
• On mineral surfaces that come into contact with the ground,
• For all kinds of reinforced concrete structures under the ground and on the ground,
• in wet areas like bathrooms, shower WC,

Features and Benefits
• Can be applied with brush or airless spray gun.
• Does not sag on vertical surfaces.
• Maintain elasticity even at low temperatures.
• it can be applied on all mineral surfaces such as concrete, stone, brick, briquette.
• it provides water isolation againstjointless, seamless and all kinds ofwater and humidity effects .
• Solvent free, non-flammable / non-flammable.
• it can be applied on dry and slightly moist surfaces.
• Crack bridge can be built.

Application lnstructions
Surface Quality: The surfaces must be clean, smooth, solid, free from any antiadhesive substance such as dust, oil, dirt, rust, mold oil, detergent and waste. lf there is segregation in concrete, it should be discarded and loose parts should be removed, weak parts should be removed. lf there is crack, hollow on the floor or wall to be applied, it should be repaired with appropriate TEKNOREP repair mortars. TEKNOMER 400 2K application should be started 3-4 days later.

Surface Preparation: The surface to be insulated must be dry. Water puddles should be removed if there is pond watering. lfthere is dilatation ofthe structure before applying TEKNOMER 400 2K, it is firstly necessary to isolate the dilatation using Teknomer Pah Bandi and TEKNOMER 400D. Later isolation of dilatations is more difficult and costly.

Surface Quality: The surfaces must be clean, smooth, solid, free from any antiadhesive substance such as dust, oil, dirt, rust, mold oil, detergent and waste. lf there is segregation in concrete, it should be discarded and loose parts should be removed, weak parts should be removed. lf there is crack, hollow on the floor or wall to be applied, it should be repaired with appropriate TEKNOREP repair mortars. TEKNOMER 400 2K application should be started 3-4 days later.

Surface Preparation: The surface to be insulated must be dry. Water puddles should be removed if there is pond watering. lfthere is dilatation ofthe structure before applying TEKNOMER 400 2K, it is firstly necessary to isolate the dilatation using Teknomer Pah Bandi and TEKNOBOND 400D.

Application Notes / Restrictions
• Foreign materials should not be added.
• it should not be applied under direct sunlight.
• Should be applied in two layers.
• it should not be applied in the rain.
• The product should not be diluted with water.
• Newly applied material is finished to cure, ete. until rain. it must be protected against weather conditions.
• Component B is added to Component A 400K, Component A in a clean container, or in its own container, which is free from any obstructive material. The product is mixed with a low speed mixer until a homogeneous mixture without lumps is obtained. Mixing time should be minimum 5min.
• Apply Teknomer 400 Astar or Teknomer 400 2K liquid component 1/1O on the surface to be applied. Atıer waiting 30 minutes to 1 hour, the mixture is applied to the surface with the ready­ to-apply product, hard-bristled brush or spraying machine. Atıer completing the reaction of the material, 2. coat application is made in the perpendicular direction of the first coat application.
• The waiting time between floors is at least 5 hours. Atıerthe first coat has been applied, it can be passed to the otherfloors when there is notrace on the fingers in the manual control. lf desired, it can be used as carrier glass fiber, reinforcement throughout the floors .
• Since the product does not have UV resistance, it is absolutely necessary to use heat insulation plates, protection plates, geotextile felt, should be covered with.
• it must be protected atıer application against adverse weather conditions such as direct sunlight, high air temperature (above +35 °C), rain and frost. The product should be cleaned thoroughly with water and detergent before it is fully cured and hardened.
• lmmediately atıer application , before hardened, the equipment should be cleaned with TEKNO Thinner. Atıerthe product is hardened, it should be cleaned by mechanical methods.